Transformer Stability Test Procedure

OBJECTIVE:

The Purpose of Differential Stability test is to determine the Healthiness of the Differential CT circuits which is protecting the in Zone equipment from actual fault conditions and through fault conditions.

Principle of Protection scheme and Testing:

This scheme is applied to protect the Equipment from the in zone faults and to avoid spurious operation of scheme due to out side zone faults.  This Differential Testing mainly carried out to ensure the correctness of CT selection and setting parameters during fault sensing. The Differential relay monitors the primary & secondary side CT currents magnitude and vectors and operates for the in zone fault conditions, restrains for the through fault conditions.

VERIFICATION OF DIFFERENTIAL SCHEME Stability:

To verify the Differential CT circuits the following test / methods are adopted,

1.    First of all the current generated during the Differential stability test is calculated using the % z voltage and source to feed the current will have to be chosen.

2.    Apply the 440 VAC supply from HV side of the Transformer in such way that Primary CT’s are included in the circuit.

3.    Short the 3 phase of the Transformer secondary side with sufficient current carrying cable after the secondary CT’s. So by step 2 & 3 Differential CT’s will see the load / fault currents.

4.    Differential Relay has to be set as per the required calculated setting values before starting the stability test. (ie: CT Ratio correction factor, Vector Correction factor)

5.    Now the 440 VAC supply can be applied to verify the stability condition. Make sure the safety that no temporary earthing / discharging of cables if it’s a live network.

6.    Now the secondary currents of Primary & secondary CT’s, Bias currents, Relay currents, Restrain currents, Operate currents can be noted down from the Relay measuring menu. At the stability condition the Primary & secondary currents magnitude and vector should match. No current should pass through the operating coil of the relay (Refer Stability Test Report & Drawings).

VERIFICATION OF DIFFERENTIAL SCHEME Sensitivity:

To verify the Differential CT circuits sensitivity the following test / methods are adopted,

1.    After verifying the Stability conditions, switch off the 3 phase supply. Primary “R” phase CT polarity should be reversed. Switch ON the 3 phase supply and verify the Differential relay operation “R” phase element. The magnitudes of Primary & secondary CT currents, relay currents, Restraining coil currents shall be noted down. Now at operating coil we can measure the operating current.

2.    Switch off the 3 phase supply and return back the Primary “R” phase CT connections to normal. Now reverse the “Y” phase CT connections. Switch ON the 3 phase supply and verify the Differential relay operation “Y” phase element. The magnitudes of Primary & secondary CT currents, relay currents, Restraining coil currents shall be noted down. Now at operating coil we can measure the operating current.

3.    Switch off the 3 phase supply and return back the Primary “Y” phase CT connections to normal. Now reverse the “B” phase CT connections. Switch ON the 3 phase supply and verify the Differential relay operation “B” phase element. The magnitudes of Primary & secondary CT currents, relay currents, Restraining coil currents shall be noted down. Now at operating coil we can measure the operating current.

4.    Normalize all the CT connections at primary side. Repeat the same above procedure for all the 3 phases at secondary side CT’s and ensure the Differential relay operation of each corresponding phase elements.

After completing the sensitivity test by reversing both side CT’s, all CT connections to be normalized and again Stability of the CT circuits to be confirmed before concluding the test. After the stability test it is advised not to touch or disturb the CT circuits of both the sides to ensure proper operation of the Differential scheme.

METHOD OF STATEMENT FOR TRANSFORMER REF STABILITY TEST

OBJECTIVE:

The Purpose of REF Differential Stability test is to determine the Healthiness of the REF Differential CT circuits which is protecting the in Zone equipment from actual fault conditions and through fault conditions.


Principle of Protection:

This scheme is applied to protect the Equipment from the in Zone Earth faults. REF Protection provides an extremely fast, sensitive and stable method of detecting winding earth faults. REF must remain stable under switching and through fault conditions. This is achieved with by including stabilizing resistor in series with REF current measuring input.


VERIFICATION OF REF DIFFERENTIAL SCHEME Stability:


To verify the REF Differential CT circuits the following test / methods are adopted,

1.    Using the Primary Injection Test set this scheme can be tested.
2.    Inject the current between “R” phase of secondary side CT and Neutral CT. Bypass the Transformer (Refer to the drawing).
3.    Verify the CT secondary currents of the Phase CT and Neutral CT’s as per the ratio and primary current injected.
4.    Verify NIL current at REF operating coil and as well in REF measurement menu.
   
VERIFICATION OF DIFFERENTIAL SCHEME Sensitivity:

To verify the Differential CT circuits sensitivity the following test / methods are adopted,

NOTE: Before starting the sensitivity test bypass or remove the REF relay as a safety measure. Also short the METROSIL and Stabilizing resistors to avoid damage.

1.    Now stop the primary injection current, reverse the “R” phase CT polarity. Inject the Primary current again and verify the operation of REF element. Note down the current at REF operating coil.

2.    At the same time note down the Voltage developed across the METROSIL and Stabilizing resistor. And verify there should be NO voltage across REF relay terminals.

3.    Bring back “R” phase CT connections to normal. Now reverse the Neutral CT connections, repeat the step 1 & 2.

4.    Follow the same above steps 1, 2 & 3 for the “Y” and “B” phase to ensure the sensitivity of REF scheme

After completing the sensitivity test by reversing the CT’s, all 3 phase CT connections to be normalized and again REF Stability of the CT circuits to be confirmed before concluding the test. After the stability test it is advised not to touch or disturb the CT circuits of both the sides to ensure proper operation of the Differential scheme.

2 comments:

Labels

PROJECTS 8086 PIN CONFIGURATION 80X86 PROCESSORS TRANSDUCERS 8086 – ARCHITECTURE Hall-Effect Transducers INTEL 8085 OPTICAL MATERIALS BIPOLAR TRANSISTORS INTEL 8255 Optoelectronic Devices Thermistors thevenin's theorem MAXIMUM MODE CONFIGURATION OF 8086 SYSTEM ASSEMBLY LANGUAGE PROGRAMME OF 80X86 PROCESSORS POWER PLANT ENGINEERING PRIME MOVERS 8279 with 8085 MINIMUM MODE CONFIGURATION OF 8086 SYSTEM MISCELLANEOUS DEVICES MODERN ENGINEERING MATERIALS 8085 Processor- Q and A-1 BASIC CONCEPTS OF FLUID MECHANICS OSCILLATORS 8085 Processor- Q and A-2 Features of 8086 PUMPS AND TURBINES 8031/8051 MICROCONTROLLER Chemfet Transducers DIODES FIRST LAW OF THERMODYNAMICS METHOD OF STATEMENTS 8279 with 8086 HIGH VOLTAGE ENGINEERING OVERVOLATGES AND INSULATION COORDINATION Thermocouples 8251A to 8086 ARCHITECTURE OF 8031/8051 Angle-Beam Transducers DATA TRANSFER INSTRUCTIONS IN 8051/8031 INSTRUCTION SET FOR 8051/8031 INTEL 8279 KEYBOARD AND DISPLAY INTERFACES USING 8279 LOGICAL INSTRUCTIONS FOR 8051/8031 Photonic Transducers TECHNOLOGICAL TIPS THREE POINT STARTER 8257 with 8085 ARITHMETIC INSTRUCTIONS IN 8051/8031 LIGHTNING PHENOMENA Photoelectric Detectors Physical Strain Gage Transducers 8259 PROCESSOR APPLICATIONS OF HALL EFFECT BRANCHING INSTRUCTIONS FOR 8051/8031 CPU OF 8031/8051 Capacitive Transducers DECODER Electromagnetic Transducer Hall voltage INTEL 8051 MICROCONTROLLER INTEL 8251A Insulation Resistance Test PINS AND SIGNALS OF 8031/8051 Physical Transducers Resistive Transducer STARTERS Thermocouple Vacuum Gages USART-INTEL 8251A APPLICATIONs OF 8085 MICROPROCESSOR CAPACITANCE Data Transfer Instructions In 8086 Processors EARTH FAULT RELAY ELECTRIC MOTORS ELECTRICAL AND ELECTRONIC INSTRUMENTS ELECTRICAL BREAKDOWN IN GASES FIELD EFFECT TRANSISTOR (FET) INTEL 8257 IONIZATION AND DECAY PROCESSES Inductive Transducers Microprocessor and Microcontroller OVER CURRENT RELAY OVER CURRENT RELAY TESTING METHODS PhotoConductive Detectors PhotoVoltaic Detectors Registers Of 8051/8031 Microcontroller Testing Methods ADC INTERFACE AMPLIFIERS APPLICATIONS OF 8259 EARTH ELECTRODE RESISTANCE MEASUREMENT TESTING METHODS EARTH FAULT RELAY TESTING METHODS Electricity Ferrodynamic Wattmeter Fiber-Optic Transducers IC TESTER IC TESTER part-2 INTERRUPTS Intravascular imaging transducer LIGHTNING ARRESTERS MEASUREMENT SYSTEM Mechanical imaging transducers Mesh Current-2 Millman's Theorem NEGATIVE FEEDBACK Norton's Polarity Test Potentiometric transducers Ratio Test SERIAL DATA COMMUNICATION SFR OF 8051/8031 SOLIDS AND LIQUIDS Speed Control System 8085 Stepper Motor Control System Winding Resistance Test 20 MVA 6-digits 6-digits 7-segment LEDs 7-segment A-to-D A/D ADC ADVANTAGES OF CORONA ALTERNATOR BY POTIER & ASA METHOD ANALOG TO DIGITAL CONVERTER AUXILIARY TRANSFORMER AUXILIARY TRANSFORMER TESTING AUXILIARY TRANSFORMER TESTING METHODS Analog Devices A–D BERNOULLI’S PRINCIPLE BUS BAR BUS BAR TESTING Basic measuring circuits Bernoulli's Equation Bit Manipulation Instruction Buchholz relay test CORONA POWER LOSS CURRENT TRANSFORMER CURRENT TRANSFORMER TESTING Contact resistance test Current to voltage converter DAC INTERFACE DESCRIBE MULTIPLY-EXCITED Digital Storage Oscilloscope Display Driver Circuit E PROMER ELPLUS NT-111 EPROM AND STATIC RAM EXCITED MAGNETIC FIELD Electrical Machines II- Exp NO.1 Energy Meters FACTORS AFFECTING CORONA FLIP FLOPS Fluid Dynamics and Bernoulli's Equation Fluorescence Chemical Transducers Foil Strain Gages HALL EFFECT HIGH VOLTAGE ENGG HV test HYSTERESIS MOTOR Hall co-efficient Hall voltage and Hall Co-efficient High Voltage Insulator Coating Hot-wire anemometer How to Read a Capacitor? IC TESTER part-1 INSTRUMENT TRANSFORMERS Importance of Hall Effect Insulation resistance check Insulator Coating Knee point Test LEDs LEDs Display Driver LEDs Display Driver Circuit LM35 LOGIC CONTROLLER LPT LPT PORT LPT PORT EXPANDER LPT PORT LPT PORT EXTENDER Life Gone? MAGNETIC FIELD MAGNETIC FIELD SYSTEMS METHOD OF STATEMENT FOR TRANSFORMER STABILITY TEST METHODS OF REDUCING CORONA EFFECT MULTIPLY-EXCITED MULTIPLY-EXCITED MAGNETIC FIELD SYSTEMS Mesh Current Mesh Current-1 Moving Iron Instruments Multiplexing Network Theorems Node Voltage Method On-No Load And On Load Condition PLC PORT EXTENDER POTIER & ASA METHOD POWER TRANSFORMER POWER TRANSFORMER TESTING POWER TRANSFORMER TESTING METHODS PROGRAMMABLE LOGIC PROGRAMMABLE LOGIC CONTROLLER Parallel Port EXPANDER Paschen's law Piezoelectric Wave-Propagation Transducers Potential Transformer RADIO INTERFERENCE RECTIFIERS REGULATION OF ALTERNATOR REGULATION OF THREE PHASE ALTERNATOR Read a Capacitor SINGLY-EXCITED SOLIDS AND LIQUIDS Classical gas laws Secondary effects Semiconductor strain gages Speaker Driver Strain Gages Streamer theory Superposition Superposition theorem Swinburne’s Test TMOD TRANSFORMER TESTING METHODS Tape Recorder Three-Phase Wattmeter Transformer Tap Changer Transformer Testing Vector group test Virus Activity Voltage Insulator Coating Voltage To Frequency Converter Voltage to current converter What is analog-to-digital conversion Windows work for Nokia capacitor labels excitation current test magnetic balance voltage to frequency converter wiki electronic frequency converter testing voltage with a multimeter 50 hz voltages voltmeter

Search More Posts

Followers